The article author is making a number of great points on A Step-by-Step Guide to Installing a Bathtub in general in the content down the page.
![Installing A Bathtub](https://www.cheatsheet.com/wp-content/uploads/2017/06/Vintage-clawfoot-bathtub.jpg?strip=all&quality=95)
Installing a bathtub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging task. If the old tub is conveniently easily accessible, the project can relocate quickly; if you need to open a wall to get rid of the old tub and position the brand-new bathtub, the task is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly require a helper to leave the old bathtub as well as set in the new one. Make certain you have actually qualified yourself for the task and fit trying it. As opposed to working with a professional to take over a halfway-completed project, it is better to think about employing one before you start. Opportunities are you might need a professional plumber to make tube links.
This write-up will certainly help you mount a brand-new bathtub in your bathroom if you have actually currently acquired a brand-new tub as well as do not require to alter the arrangement of your previous water supply pipelines.
Your devices and product list must make up the following:
- New Bathtub
- Hammer
- Pipeline Wrenches
- Prybar
- Safety Glasses
- Degree
- Pliers
- Flexible Wrench
- Putty Knife
- Screwdriver
- Cold Blade
- Tape Measure
- Pipe Caps
Preparing for the Setup
Firstly, the supporting structure supplied with the bathroom should be fitted (if needed) according to the supplier's instructions. Next off, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is important to ensure that if the faucet features a plastic washer, it is fitted in between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the faucets unit to avoid pressure on the tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you use every one of the provided washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath need to now prepare to be suited its final placement.
Removing Old Taps
If you need to replace old faucets with new ones as a part of your setup, then the first thing you ought to do is separate the water. After doing so, turn on the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be quite problematic due to the restricted gain access to that is often the case.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipes have been gotten rid of, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single faucets from transforming during this process. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Before moving on to fit the brand-new faucets, compare the pipeline links on the old taps to the new taps. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Tub
Utilizing the two wooden boards under its feet, place the bathtub in the called for position. The wooden boards are helpful in uniformly spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 little factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be accomplished by examining the spirit level and adjusting the feet on the bathtub until the spirit level reviews level.
To mount faucets, fit all-time low of the furthest flexible tap adapter to the proper supply pipe by making a compression join; after that do the very same for the various other faucet.
Switch on the water and examine all joints and new pipework for leakages and tighten them if required. Fill up the bath tub and likewise check the overflow outlet as well as the regular outlet for leaks.
Ultimately, repair the bathroom paneling as described in the manufacturer's user's manual. Tiling as well as sealing around the bathtub must wait till the bath tub has actually been utilized a minimum of when as this will certainly settle it right into its last setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, after that you will require a plastic adapter to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly require lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin guaranteeing that the washers remain in location between the tap as well as the sink. Safeguard the tap in place with the manufacturer offered backnut. When the tap is firmly in position, the supply pipes can be attached to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The previous kind should be connected to the tap ends initially, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been linked.
Tiling Around the Bath tub
In the location where the bath satisfies the ceramic tile, it is needed to secure the accompanies a silicone rubber caulking. This is very important as the fitting can move sufficient to split an inflexible seal, creating the water to pass through the wall surface in between the bath as well as the tiling, leading to issues with wetness and possible leaks to the ceiling below.
You can pick from a variety of coloured sealers to blend in your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a bigger space to load, you can load it with spins of drenched newspaper or soft rope. Remember to always fill the tub with water before sealing, to allow for the movement experienced when the tub is in use. The sealant can crack fairly very early if you do not consider this movement prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the marketplace. It is recommended to fit the tiles making use of water-resistant or water resistant adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
![How to Install a Bathtub](https://empire-s3-production.bobvila.com/blogs/wp-content/uploads/2013/07/open-uri20120628-22426-rbgg7w-0.jpg)
Hopefully you liked our excerpt on How to Install a Bathtub Yourself. Thanks a ton for finding the time to browse our blog. Those who liked our page plz remember to pass it around. Many thanks for going through it.
Instant Quote
Comments on “Getting Familiar with Plumbing: Your Starting Point for When Installing a Bathtub”